By continuing use this site, you agree to the Terms & Conditions and our use of cookies.
  • New
    Cable Pack (4-in-1) for AMS HT [CAB043]
    Cable Pack (4-in-1) for AMS HT [CAB043]
    Cable Pack (4-in-1) for AMS HT [CAB043]
    Cable Pack (4-in-1) for AMS HT [CAB043]
    Cable Pack (4-in-1) for AMS HT [CAB043]
    Cable Pack (4-in-1) for AMS HT [CAB043]
    Cable Pack (4-in-1) for AMS HT [CAB043]

    Cable Pack (4-in-1) for AMS HT [CAB043]

    Review (0)
    $24.39
    Tax included
    Auckland Local Stock

    Auckland Local Stock
    Authorized NZ Distributor – Marvle3D

    *Bambu Lab Part – Cable Pack (4-in-1) for AMS HT
    -Genuine Bambu Lab replacement cable set for AMS HT.
    -Includes four key cables for power, data, and sensors.
    -Restores stable AMS communication and performance.
    -Plug-and-play design for quick, reliable installation.
    -Ideal for fixing cable wear or signal faults in AMS HT.

    Compatible AMS: AMS HT

    Why Marvle3D?
    Marvle3D—New Zealand’s expert since 2016, offering friendly support, in-store demos, and one of the country’s largest ranges.

    Quantity :
    Hurry Up Only 5 Items left items
    Write your review
    EU3234363840424446USXX5XSSMLXLXXLXXLArm Length6161,56262,56363,56464,5Bust Circumference8084889296101106111Waist Girth6165697377828792Hip Circumference87919599103108113118
    • Security policySecurity policy(edit with the Customer Reassurance module)
    • Delivery policyDelivery policy(edit with the Customer Reassurance module)
    • Return policyReturn policy(edit with the Customer Reassurance module)

    1.Remove AMS HT from the printer and place it on a clean bench. 

    2.Open the top cover and follow the Disassembly & Assembly guide to lift the main frame; carefully unlock any ribbon/flex latches—do not pull cables by the wires. 

    3.Identify the four replacement cables (power, RS-485/bus, speed-sensor, material-selection). Keep their original routing in mind (take photos). 

    4.At the mainboard/power-board, release each old cable: press the latch, then pull the connector straight out. 

    5.Disconnect the far ends (sensor/board ends) of each cable in turn, noting orientation and keyed connectors. 

    6.Route the new cables exactly along the original channels and clips to avoid pinches and fan/heater interference. 

    7.Reconnect board-side ends first (power board and mainboard), then sensor/module ends, ensuring each connector clicks into place. 

    8.Re-seat the main frame and reattach covers per the assembly guide; verify no cables are trapped. 

    9.Reconnect the AMS HT to the printer and power on. Run a self-test/functional check (fans/heater status, feeder movement). 

    10. If you see communication or sensor errors, recheck the RS-485 and speed-sensor connections.

    Bambu Lab
    CAB043
    5 Items

    Specific References

    Write your review

    No customer reviews for the moment.

    Write your review
    Cable Pack (4-in-1) for AMS HT [CAB043]
    Cable Pack (4-in-1) for AMS HT [CAB043]

    You might also like

    Cable Pack (4-in-1) for AMS HT [CAB043]

    Cable Pack (4-in-1) for AMS HT [CAB043]

    $24.39
    Tax included